Avaya J100 Series Скачать руководство пользователя страница 391

Страница: 391 / 528

Parameter name

Default value

Description

MP_ENABLED

Specifies if the Multicast
Paging feature is enabled
on the phone.

This is the basic
parameter for this feature.
If this parameter is not set,
other parameters listed
below will be ignored.

Valid values:

• 0: Multicast Paging is

disabled.

• 1: Multicast Paging is

enabled.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

391

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 391 / 528

Результаты поиска

Содержание J100 Series

Отзывы: