manualshive.com logo in svg

Avaya J100 Series, Установка и администрирование, Страница: 408 / 528

Поделиться
Скачать
Avaya J100 Series Скачать руководство пользователя страница 408

Parameter name

Default value

Description

PHY2VLAN

0

Specifies the value of the
802.1Q VLAN ID used by
frames forwarded to and
from the secondary
(PHY2) Ethernet interface
when VLAN separation is
enabled.

Valid values are 0 through
4094.

Note:

The parameter is
configured through
the following:

• SET command in a

settings file

• LLDP

PKCS12_PASSWD_RETRY

3

Specifies the number of
retries for entering
PKCS12 file password. If
user failed to enter the
correct PKCS12 file
password after
PKCS12_PASSWD_RET
RY retries, then the phone
will continue the startup
sequence without
installation of PKCS12 file.
Valid values are from 0 to
100.

Value operation:

• 0: No retry

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

408

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов