manualshive.com logo in svg

Avaya J100 Series, Установка и администрирование, Страница: 476 / 528

Поделиться
Скачать
Avaya J100 Series Скачать руководство пользователя страница 476

Parameter name

Default value

Description

VLANSEPMODE

0

1 for J129

Specifies whether full
VLAN separation is be
enabled by the built-in
Ethernet switch while the
telephone is tagging
frames with a non-zero
VLAN ID. This VLAN
separation is enabled
when: VLANSEP=1,
L2QVLAN and
PHY2VLAN have non-zero
values, L2Q is auto (0) or
(1) tagging.PHY2PRIO is
not supported when
VLANSEPMODE is 1.

Value operation:

• 0: Disabled

• 1: Enabled

Note:

This parameter is
configured through
the settings file.

VLANTEST

60

Specifies the number of
seconds that the phone
waits prior to failing back
to a different VLAN ID if no
response is received from
the DHCP server.

Valid values are 0 through
999.

A value of zero means that
DHCP tries with a non-
zero VLAN ID forever.

Note:

This parameter is
configured through:

• Settings file

• A name equal to

value pair in
DHCPACK
message

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

476

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов