Avaya J100 Series Скачать руководство пользователя страница 183

Страница: 183 / 528

Parameter name

Default Value

Description

EXCHANGE_SERVER_MODE

Specifies the protocol to be used
to contact Exchange servers.

Value operation:

• 1: Use WebDAV

• 2: Use Exchange Web Services

(EWS)

• 3: Try EWS first, if that fails, try

WebDAV.

EXCHANGE_SERVER_SECURE
_MODE

Specifies if HTTPS should be
used to contact Exchange
servers.

Value operation:

• 0: Use HTTP

• 1: Use HTTPS

ENABLE_EXCHANGE_REMIND
ER

Specifies whether or not
exchange reminders will be
displayed.

Value operation:

• 0: Not displayed

• 1: Displayed

EXCHANGE_SNOOZE_TIME

Specifies the number of minutes
in which a reminder must be
displayed again after it is
temporarily dismissed.

Valid values are 0 through 60.

Table continues…

Application configuration

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

183

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 183 / 528

Результаты поиска

Содержание J100 Series

Отзывы: