Avaya J100 Series Скачать руководство пользователя страница 389

Страница: 389 / 528

Parameter name

Default value

Description

MEDIA_NEG_PREFERENCE

Specifies the address
family preference used by
a dual mode answer in
non-Avaya environment.
This parameter is not
applicable for single mode
phones.

Value operation:

• 0: Remote or offerer's

preference

• 1: Local

MEDIA_PRESERVATION

Supports media
preservation when
ENABLE_IPOFFICE is set
to 2.

Value operation:

• 0: Phone tries to

preserve a call for a
duration specified by
PRESERVED_CALL_D
URATION settings
parameter.

• 1: Phone does not

preserve a call. As soon
as the phone detects link
failure to IP Office, the
phone drops a call and
makes re-registration
attempt.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

389

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 389 / 528

Результаты поиска

Содержание J100 Series

Отзывы: