Avaya J100 Series Скачать руководство пользователя страница 473

Страница: 473 / 528

Parameter name

Default value

Description

USBPOWER

Controls USB power when
power is provided to the
USB interface.

Value operation:

• 0: Turn off USB power

regardless of power
source.

• 1: Turn on USB power

only if Aux powered.

• 2: Turn on USB power

regardless of power
source.

• 3: Turn on USB power if

Aux powered or PoE
Class 3 power.

Note:

This parameter is
supported only in
Avaya J159 IP Phone

USE_CONTACT_IN_REFERTO

Specifies which transfer
target address should be
used in Refer-To a header
of REFER SIP request on
attended transfer.

Value operation:

• 0: Use CONTACT URI of

the transfer target in
Refer-To header of
REFER SIP request.

• 1: Use TO URI of the

transfer target in Refer-
To header of REFER
SIP request.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

473

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 473 / 528

Результаты поиска

Содержание J100 Series

Отзывы: