manualshive.com logo in svg

Avaya J100 Series, Установка и администрирование, Страница: 462 / 528

Поделиться
Скачать
Avaya J100 Series Скачать руководство пользователя страница 462

Parameter name

Default value

Description

STUN_SERVER_ADDRESS

Null

This is the basic STUN
parameter defining the
STUN server address.
Other parameters listed
below will be ignored if this
parameter is not set.

The valid value is an IPv4
address in the dotted
decimal format or a
FQDN.

Note:

If specified as an IPv4 address, the
STUN server port will default to
3478. It is applicable only when
3PCC_SERVER_MODE=0 or
3PCC_SERVER_MODE=2 and
ENABLE_3PCC_ENVIRONMENT=1

The following characters
are allowed:

• 0 – 9

• a – z

• A – Z

• dot (“.”)

For example,

 SET

STUN_SERVER_ADDRESS
192.168.161.54

STUN_UDP_INITIAL_TIMEOUT_MSEC

500

Determines the initial
timeout, in milliseconds, to
wait for a Response to a
STUN Request sent over
UDP. The timeout value is
internally doubled after
each (re)transmission.

Valid values are positive
integers from 500 (0,5
sec) to 3000 (3 sec).

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

462

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов