manualshive.com logo in svg

Avaya J100 Series, Установка и администрирование, Страница: 478 / 528

Поделиться
Скачать
Avaya J100 Series Скачать руководство пользователя страница 478

Parameter name

Default value

Description

WAIT_FOR_UNREGISTRATION_TIMER

32

Specifies the number of
seconds the phone waits
before assuming that an
un-registration request is
complete.

Un-registration includes
termination of registration
and all active dialogs.

Valid values are 4 through
3,600.

WARNING_FILE

Null

Specifies the file name or
URL for a custom single-
channel WAV file coded in
ITU-T G.711 u-law or A-
law PCM with 8-bit
samples at 8kHz to be
used as a call recording
warning instead of the
built-in English warning.

The value can contain 0 to
255 characters.

WBCSTAT

1

Specifies whether a
wideband codec indication
is displayed when a
wideband codec is used.

Value operation:

0: Disabled

1: Enabled

Note:

J129 does not
support this
parameter

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

478

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов