Avaya J100 Series Скачать руководство пользователя страница 485

Страница: 485 / 528

Parameter Name

Default Value

Description

WEP_DEFAULT_KEY

N/A

Specifies the index of WEP
default key.

Value operation:

•

WLAN_COUNTRY

Specifies the ISO country code
representing the Wi-Fi regulatory
domain.

WLAN_ENABLE_80211D

Enables the phone to configure
its Wi-Fi regulatory domain to
match the 802.11d.

Value operation:

•

: Disable

•

: Enable

WEP_KEY_LEN

128 bit

Specifies the length of the WEP
key.

Value operation:

•

40 bit

•

64 bit

•

128 bit

WLAN_PASSWORD

N/A

Specifies the pre-configured Wi-Fi
network password. This
parameter is applicable if the
WIFISTAT is enabled and
WLAN_SECURITY is

wpa2psk

or WLAN_SECURITY is

wpa2e

WLAN_WPA2E_EAP_METHOD
is

PEAP

and

WLAN_WPA2E_EAP_PHASE2 is

MSCHAPV2

The password must be from 8 to
63 characters. Note that the
space and ASCII 0x20 are not
supported.

Table continues…

List of Wi-Fi configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

485

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 485 / 528

Результаты поиска

Содержание J100 Series

Отзывы: