Avaya J100 Series Скачать руководство пользователя страница 346

Страница: 346 / 528

Parameter name

Default value

Description

DOWNLOADABLE_DIRECTORY

Null

Specifies the file name of
the contacts directory.

The value can contain 0 to
32 ASCII characters.

Important:

The file name must
be in .xml format.

DOT1X

Specifies the 802.1X pass-
through operating mode.

Pass-through is the
forwarding of EAPOL
frames between the phone
Ethernet line interface and
its secondary (PC)
Ethernet interface

Value operation:

• 0: EAPOL multicast

pass-through enabled
without proxy logoff.

• 1: EAPOL multicast

pass-through enabled
with proxy logoff.

• 2: EAPOL multicast

pass-through disabled.

DOT1XEAPS

MD5

Specifies the
authentication method to
be used by 802.1X.

Valid values are MD5, and
TLS.

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

346

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 346 / 528

Результаты поиска

Содержание J100 Series

Отзывы: