Avaya J100 Series Скачать руководство пользователя страница 28

Страница: 28 / 528

Wall mounting Avaya J100 Expansion Module

About this task

If your phone is wall mounted, you must additionally install the wall mount for the Avaya J100

Expansion Module. You must separately purchase the wall mount for the expansion module. The

part number of the wall mount kit is 700514338.

Before you begin

Obtain the following items:

• Wall mount kit, containing a wall mount bracket.
• Two #8 screws. The screws are not provided with the wall mounting kit.

Procedure

1. Remove the phone from the wall mount.

Initial setup and connectivity

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 28 / 528

Результаты поиска

Содержание J100 Series

Отзывы: