Avaya J100 Series Скачать руководство пользователя страница 257

Страница: 257 / 528

Parameter name

Default value

Description

SOFTKEY_CONFIGURATION

0,1,2

Specifies which feature will show
up on which soft key on the
Avaya J129 IP Phone screen.

The features are defined as
follows:

• 0 = Redial

• 1 = Contacts

• 2 = Emergency

• 3 = Recents

• 4 = Voicemail

Note:

Emergency calls are not
supported in an Open SIP
environment.

Feature configuration

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

257

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 257 / 528

Результаты поиска

Содержание J100 Series

Отзывы: