Avaya J100 Series Скачать руководство пользователя страница 406

Страница: 406 / 528

Parameter name

Default value

Description

cannot be changed by
the user.

Note:

Avaya J129 IP Phone
does not support this
feature.

PHY1STAT

Specifies the speed and
duplex settings for the
Ethernet line interface.

Value operation:

• 1: auto-negotiate

• 2: 10Mbps half-duplex

• 3: 10Mbps full-duplex

• 4: 100Mbps half-duplex

• 5: 100Mbps full-duplex

• 6: 1Gbps full-duplex, if

supported by hardware,
otherwise auto-
negotiated

PHY2_AUTOMDIX_ENABLED

Specifies whether auto-
MDIX is enabled on PHY2.

Value operation:

• 0: auto-MDIX is

disabled.

• 1: auto-MDIX is enabled.

PHY2PRIO

Specifies the layer 2
priority value to be used
for frames received on the
secondary Ethernet
interface when VLAN
separation is enabled.

Valid values are 0 through
7.

Note:

J129 does not
support this
parameter.

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

406

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 406 / 528

Результаты поиска

Содержание J100 Series

Отзывы: