Avaya J100 Series Скачать руководство пользователя страница 44

Страница: 44 / 528

Parameter name

Default Value

Description

ENABLE_3PCC_ENVIRONMENT 1

Specifies whether the deployment
environment is an Open SIP
server.

Value operation:

• 0: Avaya environment.

• 1 (Default): Open SIP

environment.

3PCC_SERVER_MODE

Specifies if the phone expects a
generic Open SIP server or a
BroadSoft server (applicable
when
ENABLE_3PCC_ENVIRONMENT
is set to 1).

Value operation:

• 0 (Default): Generic.

• 1: BroadSoft.

ENABLE_OOD_RESET_NOTIFY 0

Specifies whether the phone
supports Out Of Dialog (OOD)
SIP NOTIFY message with
Event:resync or Event:check-sync
only.

Value operation:

• 0 (Default): OOD is not

supported.

• 1: OOD is supported.

To support Broadsoft Device
Management, this value should
be set to 1.

Table continues…

Open SIP operation modes

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 44 / 528

Результаты поиска

Содержание J100 Series

Отзывы: