Avaya J100 Series Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 528

Avaya J100 Series Скачать руководство пользователя страница 32

Activate

auto config?

DHCP Option 242

DES

Config URL

found?

Connect to

config URL

Config URL

found?

DHCP Option 242

Config URL

found?

Connect to

config URL

Done

Enrollment

code?

Connect to

config URL

Success?

Prompt for

Config URL

Code

Yes

Yes

Yes

Yes

Yes

Cancel

Bootup

Timeout

No

No

No

No

No

Provisioning server mutual authentication support

You can use the Device Enrollment Services (DES) server to install a DES-HSM root certificate on
the phone for mutual TLS authentication with a provisioning server.

During mutual TLS authentication, the phone validates the certificate provided by the provisioning
server and, in its turn, presents an identity certificate to the provisioning server. To validate it, the
provisioning server must trust the root CA certificate used for issuing the phone identity certificate.

Initial setup and connectivity

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

32

Comments on this document? [email protected]

«
...
30
31
32
33
34
...
»

Содержание J100 Series

















































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов