Avaya J100 Series Скачать руководство пользователя страница 382

Страница: 382 / 528

Parameter name

Default value

Description

LLDP_ENABLED

Specifies whether LLDP is
enabled.

Value operation:

• 0: Disabled

• 1: Enabled

• 2: Enabled, but only

begins transmitting if an
LLDP frame is received.

LOCAL_DIAL_AREA_CODE

Specifies if user must dial
area code for calls within
same area code regions.

Value operation:

• 0: User don't need to

dial area code.

• 1: User need to dial area

code. When enabled,
the area code parameter
(PHNLAC) should also
be configured.

Note:

This parameter is
supported when the
phone is failed over.

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

382

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 382 / 528

Результаты поиска

Содержание J100 Series

Отзывы: