Avaya J100 Series Скачать руководство пользователя страница 450

Страница: 450 / 528

Parameter name

Default value

Description

SIP_CONTROLLER_LIST_2

Null

This parameter replaces
SIP_CONTROLLER_LIST
for dual mode phones. It is
used to select the
registration address.

SIP_CONTROLLER_LIST
_2 is used on IPv6-only
phones to provide the list
of SIPv6 servers. SIPv4
servers are ignored in
IPv6-only mode.

Valid values are 0 to 255
characters in the dotted
decimal or colon-hex
format, separated by
commas without any
intervening spaces.

The SIP Proxy list has the
following format:

host[:port]
[;transport=xxx]

where

•

host

is IP addresses in

dotted-decimal format or
hex format.

•

[:port]

is the port

number. The default
value is 5,061 for TLS.

•

[;transport=xxx]

an optional transport
type where

xxx

is either

TLS or TCP The default
value is TLS.

A dual mode controller has
addresses of both families
within curly ({ }) brackets.

This parameter should not
be set and left at default.

Open SIP redundancy do
not support IPv6.

Table continues…

Customizable parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

450

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 450 / 528

Результаты поиска

Содержание J100 Series

Отзывы: