Avaya J100 Series Скачать руководство пользователя страница 353

Страница: 353 / 528

Parameter name

Default value

Description

ENABLE_DND_PRIORITY_OVER_CFU_CFB

Specifies that the Do-not-
disturb (DND) feature is
given priority over Call
forwarding unconditionally
(CFU) and Call forwarding
busy (CFB).

Value operation:

• 0: Disabled

• 1: Enabled

Note:

This parameter is
only applicable if an
Open SIP
environment is
configured.

ENABLE_EARLY_MEDIA

Specifies if the phone sets
up a voice channel to the
called party before the call
is answered.

Value operation:

• 0: No

• 1: Yes

Setting this parameter to 1
can speed up call setup.

ENABLE_EXCHANGE_REMINDER

Specifies whether or not
exchange reminders will
be displayed.

Value operation:

• 0: Not displayed

• 1: Displayed

Note:

Only Avaya J129 IP
Phone supports this
feature.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

353

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 353 / 528

Результаты поиска

Содержание J100 Series

Отзывы: