Avaya J100 Series Скачать руководство пользователя страница 307

Страница: 307 / 528

Parameter name

Default value

Description

BLF_PARKED_CALL_INDICATION

Specifies the indication
type for a BLF parked call.

Valid values:

• 0 - None (no alerting for

BLF parked calls).

• 1 - Default (the behavior

based on
BLF_PARKED_CALL_IN
DICATION_MODE
parameter value).

• 2 - Audible (only audible

alerting for BLF parked
call).

• 3 - Visual (only visual

alerting for BLF parked
call).

• 4 - Both (default - both

audible and visual
alerting for BLF parked
call).

Note:

This parameter is
supported only in the
3PCC environment.

Avaya J129 IP Phone
does not support this
feature.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

307

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 307 / 528

Результаты поиска

Содержание J100 Series

Отзывы: