Avaya J100 Series Скачать руководство пользователя страница 293

Страница: 293 / 528

Parameter name

Default value

Description

ACOUSTIC_EXPOSURE_PROTECT_MODE_DEFAULT

Off

Specifies the long-term
acoustic exposure
protection mode default
setting.

Value operation:

• Off

• Dynamic:

• 4 hours

• 8 hours

Note:

Avaya J129 IP Phone
does not support
long-term acoustic
exposure protection.

ADMIN_LOGIN_ATTEMPT_ALLOWED

Specifies the allowed
number of failed attempts
for accessing the

Admin

menu.

ADMIN_LOGIN_LOCKED_TIME

Specifies the duration for
lockout when a user
reaches the maximum
attempts limit for
accessing the

Admin

menu.

Valid values are from 5
min to 1,440 min.

ADMIN_PASSWORD

27238

Specifies an access code
for accessing the

Admin

menu.

Valid values are from 6 to
31 alphanumeric
characters.

Note:

If this parameter
length is set below 6
or above 31
alphanumeric
characters, then the
parameter is treated
as not defined.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

293

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 293 / 528

Результаты поиска

Содержание J100 Series

Отзывы: