Avaya J100 Series Скачать руководство пользователя страница 104

Страница: 104 / 528

Name

Description

Redirect Message Control

Specifies whether the ICMP redirect messages are
processed or not.

The options are:

•

Yes

•

No (default)

TCP

Send TCP Keep Alive Message

Specifies whether the TCP/IP keep-alive messages
are enabled or disabled in the system.

The options are:

•

Enable (default)

•

Disable

TCP Keep Alive Time

Specifies the wait time interval in seconds of the
phone before sending out the TCP keep-alive
message (TCP ACK message) to the far-end.

Valid value is an integer from 10 to 3600. The
default option is 60 seconds.

TCP Keep Alive Interval

Specifies the TCP keep-alive packet re-
transmission interval.

Valid value is an integer from 5 to 60. The default
option is 10 seconds.

Web Server

Web Server On HTTP

Specifies whether HTTP access to the web
interface is enabled or disabled.

The options are:

•

Yes (default)

•

HTTP Listen Port

Specifies the port number of the web server when
the web interface is accessed using HTTP.

The valid value is an integer from 80 to 65535. The
default port number is 80.

HTTPS Listen Port

Specifies the port number of the web server when
the web interface is accessed using HTTPS.

The valid value range is from 443 to 65535. The
default port number is 443.

The valid value is an integer from 443 to 65535.

Table continues…

Phone configuration

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

104

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 104 / 528

Результаты поиска

Содержание J100 Series

Отзывы: