Avaya J100 Series Скачать руководство пользователя страница 297

Страница: 297 / 528

Parameter name

Default value

Description

AUDASYS

Specifies the audible
alerting setting for the
phone.

Value operation:

• 0: Turns off audible

alerting. User cannot
adjust ringer volume.

• 1: Turns on audible

alerting. User can adjust
ringer volume, but
cannot turn off audible
alerting.

• 2: Turns off audible

alerting. User can adjust
ringer volume and can
turn off audible alerting.

• 3: Turns on audible

alerting. User can adjust
ringer volume and can
turn off audible alerting.

Note:

Avaya J129 IP Phone
does not support this
parameter.

AUDIOENV

Specifies the audio
environment index and
enables you to customize
the phone's audio
performance.

Valid values are 0 through
299.

This parameter affects
settings for AGC dynamic
range and handset noise
reduction thresholds.
Always consult Avaya
before changing this
parameter.

Table continues…

List of configuration parameters

April 2020

Installing and Administering Avaya J100 series IP Phones in an Open SIP

environment

297

Comments on this document? [email protected]

Содержание J100 Series

















































































































































































































































































































































































































































































































































Результаты поиска

Содержание J100 Series

Отзывы:

Avaya J100 Series, Установка и администрирование, Страница: 297 / 528

Результаты поиска

Содержание J100 Series

Отзывы: