ABB ACQ810 Скачать руководство пользователя страница 170 | Manualshive

Страница: 170 / 376

ABB ACQ810 Скачать руководство пользователя страница 170

170 Parameters

19.09

Speed TripMargin

Defines, together with

Maximum speed

and

Minimum speed

, the maximum allowed speed of the motor

(overspeed protection). If actual speed (

) exceeds the speed limit defined by parameter

or

by more than the value of this parameter, the drive

trips on the

fault.

Example:

If the maximum speed is 1420 rpm and speed trip

margin is 300 rpm, the drive trips at 1720 rpm.

0.0 … 10000.0 rpm

Overspeed trip margin.

10 = 1 rpm

19.10

Speed window

Defines the absolute value for the motor speed window
supervision, i.e. the absolute value for the difference
between the actual speed and the unramped speed
reference (

Motor speed rpm

). When the motor speed is within the limits defined

by this parameter, signal

bit 8

(AT_SETPOINT) is 1. If the motor speed is not within the
defined limits, bit 8 is 0.

0 … 30000 rpm

Absolute value for motor speed window supervision.

1 = 1 rpm

20

20 Limits

Drive operation limits.
See also section

Speed controller tuning

.

20.01

Maximum speed

Defines the allowed maximum speed.

0 … 30000 rpm

Maximum speed.

1 = 1 rpm

20.02

Minimum speed

Defines the allowed minimum speed.

Note:

If the motor may only be run in the forward direction

within a certain range above 0 rpm, leave this parameter at
0 rpm, and use parameter

SpeedRef min abs

to define

the lower boundary of the range.

-30000 … 0 rpm

Minimum speed.

1 = 1 rpm

No.

Name/Value

Description

FbEq

Speed trip margin

Speed trip margin

Speed

Time

«
...
168
169
170
171
172
...
»

Содержание ACQ810

























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды