manualshive.com logo in svg

ABB ACQ810, Руководство по прошивке

Поделиться
Скачать
ABB ACQ810 Скачать руководство пользователя страница 284

284   Parameters

0.0 … 6400.0 A

Nominal current of the motor. The allowable range is 1/6…2 
× 

I

max

 of the drive (0…2 ×

I

max

 with scalar control mode).

10 = 1 A

99.07

Mot nom voltage

Defines the nominal motor voltage as fundamental phase-to-
phase rms voltage supplied to the motor at the nominal 
operating point. This setting must match the value on the 
rating plate of the motor.

Notes:

•  The stress on the motor insulation is always dependent 

on the drive supply voltage. This also applies to the case 
where the motor voltage rating is lower than that of the 
drive and the supply.

•  This parameter cannot be changed while the drive is 

running.

1/6 … 2 × 

U

N

Nominal voltage of the motor.

10 = 1 V

99.08

Mot nom freq

Defines the nominal motor frequency.

Note:

 This parameter cannot be changed while the drive is 

running.

5.0 … 500.0 Hz

Nominal frequency of the motor.

10 = 1 Hz

99.09

Mot nom speed

Defines the nominal motor speed. The setting must match 
the value on the rating plate of the motor.

Notes:

• For safety reasons, after ID run, the maximum and 

minimum speed limits (parameters 

16.17

 and 

16.17

) are 

automatically set to 1.2 times the value of this parameter.

• This parameter cannot be changed while the drive is 

running.

0 … 30000 rpm

Nominal speed of the motor.

1 = 1 rpm

99.10

Mot nom power

Defines the nominal motor power. The setting must match 
the value on the rating plate of the motor. If multiple motors 
are connected to the drive, enter the total power of the 
motors.
The unit is selected by parameter 

16.17

 

Power unit

.

Note:

 This parameter cannot be changed while the drive is 

running.

0.00 … 10000.00 
kW

Nominal power of the motor.

100 = 1 kW

99.11

Mot nom cosfii

Defines the cosphi of the motor for a more accurate motor 
model. Not obligatory; if set, should match the value on the 
rating plate of the motor.

Note:

 This parameter cannot be changed while the drive is 

running.

0.00 … 1.00

Cosphi of the motor.

100 = 1

99.12

Mot nom torque

Defines the nominal motor shaft torque for a more accurate 
motor model. Not obligatory.

Note:

 This parameter cannot be changed while the drive is 

running.

0 … 2147483.647 
Nm

Nominal motor torque.

1000 = 1 N•m

No.

Name/Value

Description

FbEq

Содержание ACQ810

























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды