ABB ACQ810 Скачать руководство пользователя страница 167

Страница: 167 / 376

Parameters 167

M lvl short

A selective list of parameters relevant to the Level control
application macro (multipump) is displayed.

M lvl long

A more comprehensive list of parameters relevant to the
Level control application macro (multipump) is displayed.

M pump short

A selective list of parameters relevant to the Multipump
control application macro (single-pump) is displayed.

M pump long

A more comprehensive list of parameters relevant to the
Multipump control application macro (single-pump) is
displayed.

Full

All parameters are displayed.

16.17

Power unit

Selects the unit of power for parameters such as

Kilowatt.

Horsepower.

16.20

Macro selected

Shows which application macro is currently selected. For
more information, see chapter

Application macros

(page

Note:

Changing the value of this parameter does not change

the current application macro. To change the application
macro, use the Application macro assistant available
through the control panel instead.

Factory def

Factory default macro.

Ext ctrl

External control macro.

Trad ctrl

Traditional pump control macro.

Hand/Auto

Hand/Auto macro.

Level ctrl

Level control macro (for a single pump).

Multi level

Level control macro (for multiple pumps).

Multi pump

Multipump control macro.

16.21

Menu selection

Loads a short, long or full parameter list.

Short

Only a selective list of parameters will be displayed.

Long

Only the parameters relevant to the current application
macro are displayed.

Full

All parameters are displayed, including those not relevant to
the current application macro.

19 Speed calculation

Speed scaling, feedback and supervision settings.

19.01

Speed scaling

Defines the terminal speed value used in acceleration and
the initial speed value used in deceleration (see parameter
group

22 Speed ref ramp

). Also defines the rpm value that

corresponds to 20000 for fieldbus communication with ABB
Drives communication profile.

0 … 30000 rpm

Acceleration/deceleration terminal/initial speed.

1 = 1 rpm

19.02

Speed fb sel

Selects the speed feedback value used in control.

Note:

The speed feedback value is always estimated.

Estimated

A calculated speed estimate is used.

No.

Name/Value

Description

FbEq

Содержание ACQ810
























































































































































































































































































































































































Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды

ABB ACQ810, Руководство по прошивке

Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды