ABB ACQ810 Скачать руководство пользователя страница 183

Страница: 183 / 376

Parameters 183

23.20

PI tune mode

Activates the speed controller autotune function.
The autotune will automatically set parameters

and

, as well as

. If the

autotune mode is chosen, also

23.07

Speed err Ftime

is automatically set.

The status of the autotune routine is shown by parameter

06.03

Speed ctrl stat

WARNING!

The motor will reach the torque and

current limits during the autotune routine. ENSURE
THAT IT IS SAFE TO RUN THE MOTOR BEFORE

PERFORMING THE AUTOTUNE ROUTINE!

Notes:

• Before using the autotune function, the following

parameters should be set:
• All parameters adjusted during the start-up as

described in the

ACQ810-04 drive modules Start-up

Guide

•

•

•

• Speed reference ramp settings in group

•

• The drive must be in local control mode and stopped

before an autotune is requested.

• After requesting an autotune with this parameter, start the

drive within 20 seconds.

• Wait until the autotune routine is completed (this

parameter has reverted to the value

Done

). The routine

can be aborted by stopping the drive.

• Check the values of the parameters set by the autotune

function.

Содержание ACQ810
























































































































































































































































































































































































Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды

ABB ACQ810, Руководство по прошивке

Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды