ABB ACQ810 Скачать руководство пользователя страница 234

Страница: 234 / 376

234 Parameters

56.06

Signal3 mode

Defines the way the signal selected by parameter

56.03

Signal3 param

is displayed on the optional control panel.

Disabled

Signal not displayed. Any other signals that are not disabled
are shown together with their respective signal name.

-1

Normal

Shows the signal as a numerical value followed by unit.

Bar

Shows the signal as a horizontal bar.

Drive name

Shows the drive name. (The drive name can be set using the
DriveStudio PC tool.)

Drive type

Shows the drive type.

56.07

Local ref unit

Defines how speed reference is entered and displayed by
the control panel and DriveStudio PC tool. Also determines
the unit of signal

02.34

Panel ref

Note:

This parameter also applies to external control when

speed reference is given from the control panel.

rpm

Speed reference is displayed and entered in rpm.

Percent

Speed reference is displayed and entered in percent. The
scaling is as follows:

58 Embedded Modbus

Configuration parameters for the embedded fieldbus (EFB)
interface.
See also chapter

Control through the embedded fieldbus

interface

on page

329

58.01

Protocol ena sel

Enables/disables the embedded fieldbus communication
protocol.

Note:

When the embedded fieldbus interface is enabled, the

drive-to-drive link operation (parameter group 76) is
automatically disabled.

Disabled

Disabled.

Modbus RTU

Modbus RTU protocol enabled.

58.03

Node address

Defines the node address.

0…247

Node address.

1 = 1

58.04

Baud rate

Selects the baud rate of the RS-485 link.

4800

4.8 kbit/s.

9600

9.6 kbit/s.

19200

19.2 kbit/s.

38400

38.4 kbit/s.

57600

57.6 kbit/s.

76800

76.8 kbit/s.

No.

Name/Value

Description

FbEq

20.01

Maximum speed

Control panel

reference

Speed (rpm)

100%

-100%

20.02

Minimum speed

Содержание ACQ810
























































































































































































































































































































































































Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды

ABB ACQ810, Руководство по прошивке

Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды