manualshive.com logo in svg

ABB ACQ810, Руководство по прошивке

Поделиться
Скачать
ABB ACQ810 Скачать руководство пользователя страница 237

Parameters   237

0…65535

No. of messages with CRC errors.

1 = 1

58.21

Raw CW LSW

Shows the LSW part of the Control Word which the drive 
receives from the Modbus master. Read only.

0x0000…0xFFFF

Bits 0…15 of the Control word as a hex value.

1 = 1

58.22

Raw CW MSW

Shows the MSW part of the Control Word which the drive 
receives from the Modbus master.  Read only.

0x0000…0xFFFF

Bits 16…32 of the Control word as a hex value.

1 = 1

58.23

Raw SW LSW

Shows the LSW part of the Status Word which the drive 
sends  to the Modbus master. Read only. 

0x0000…0xFFFF

Bits 0…15 of the Status word as a hex value.

1 = 1

58.24

Raw SW MSW

Shows the MSW part of the Status Word which the drive 
sends to the Modbus master. Read only.

0x0000…0xFFFF

Bits 16…32 of the Status word as a hex value.

1 = 1

58.25

Raw Ref 1 LSW

Shows the LSW part of reference 1 which the drive receives 
from the Modbus master. Read only.

0x0000…0xFFFF

Bits 0…15 of reference 1 as a hex value.

1 = 1

58.26

Raw Ref 1 MSW

Shows the MSW part of reference 1 which the drive receives 
from the Modbus master. Read only. 

0x0000…0xFFFF

Bits 16…32 of reference 1 as a hex value.

1 = 1

58.27

Raw Ref 2 LSW

Shows the LSW part of reference 2 which the drive receives 
from the Modbus master. Read only.

0x0000…0xFFFF

Bits 0…15 of reference 2 as a hex value.

1 = 1

58.28

Raw Ref 2 MSW

Shows the MSW part of reference 2 which the drive receives 
from the Modbus master. Read only.

0x0000…0xFFFF

Bits 16…32 of reference 2 as a hex value.

1 = 1

58.30

Transmit delay

Defines the delay time which the slave waits until it sends a 
response.

0…65335 ms

Transmit delay time.

1 = 1 ms

58.31

Ret app errors

Selects whether the drive returns Modbus exception codes 
or not.

No

No

0

Yes

Yes

1

58.32

Word order

Defines the order of the data words in the Modbus frame.

MSW LSW

Most significant word first, then Least significant word.

0

LSW MSW

Least significant word first, then Most significant word.

1

58.35

Data I/O 1

Defines the address of the drive parameter which the 
Modbus master accesses when it reads from or writes to the 
register address corresponding to Modbus In/Out parameter 
no. 1. The Modbus master defines the type of the data (input 
or output).
The value is conveyed in a Modbus frame using two 16-bit 
words. If the drive parameter is a 16-bit value, the LSW 
(Least significant word) conveys the value. If the drive 
parameter is a 32-bit value, the next Modbus In/Out 
parameter is also reserved.

0…9999

Parameter address. Format: xxyy, where: 
xx = parameter group 
yy = parameter index

1 = 1

No.

Name/Value

Description

FbEq

Содержание ACQ810

























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды