ABB ACQ810 Скачать руководство пользователя страница 317 | Manualshive

Страница: 317 / 376

ABB ACQ810 Скачать руководство пользователя страница 317

Fault tracing 317

2049

MOTTEMPAL2
(0x4313)

Programmable alarm:

Mot temp2 prot

Estimated motor
temperature (based on
motor thermal model) has
exceeded alarm limit
defined by parameter

Mot temp2 almLim

.

Check motor ratings and load.
Let motor cool down. Ensure proper
motor cooling: Check cooling fan, clean
cooling surfaces, etc.
Check value of alarm limit.
Check motor thermal model settings
(parameters

…

).

Measured motor
temperature has exceeded
alarm limit defined by
parameter

Check that actual number of sensors
corresponds to value set by parameter

Mot temp2 src

.

Check motor ratings and load.
Let motor cool down. Ensure proper
motor cooling: Check cooling fan, clean
cooling surfaces, etc.
Check value of alarm limit.

2050

IGBTOLALARM
(0x5482)

Excessive IGBT junction to
case temperature. This fault
protects the IGBT(s) and
can be activated by a short
circuit in the motor cable.

Check motor cable.

2051

IGBTTEMPALARM
(0x4210)

Drive IGBT temperature is
excessive.

Check ambient conditions.
Check air flow and fan operation.
Check heatsink fins for dust pick-up.
Check motor power against drive power.

2052

COOLALARM
(0x4290)

Drive module temperature is
excessive.

Check ambient temperature. If it exceeds
40 °C (104 °F), ensure that load current
does not exceed derated load capacity of
drive. See appropriate

Hardware Manual.

Check drive module cooling air flow and
fan operation.
Check inside of cabinet and heatsink of
drive module for dust pick-up. Clean
whenever necessary.

2053

MENU CHG
PASSWORD REQ
(0x6F81)

Loading a parameter listing
requires a password.

Enter password at parameter

2054

MENU CHANGED
(0x6F82)

A different parameter listing
is being loaded.

Informative alarm.

Code

Alarm (fieldbus code),
other information

Cause

What to do

«
...
315
316
317
318
319
...
»

Содержание ACQ810

























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды