ABB ACQ810 Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 376

ABB ACQ810 Скачать руководство пользователя страница 80

80 Program features

Earth fault detection (parameter

)

The earth fault detection function is based on sum current measurement. Note that

• an earth fault in the supply cable does not activate the protection
• in a grounded supply, the protection activates in 200 milliseconds
• in an ungrounded supply, the supply capacitance should be 1 microfarad or more
• the capacitive currents caused by shielded motor cables up to 300 metres will not

activate the protection

• the protection is deactivated when the drive is stopped.

Supply phase loss detection (parameter

)

The parameter selects how the drive reacts whenever a supply phase loss is
detected.

Safe torque off detection (parameter

The drive monitors the status of the Safe torque off input. For more information on the
Safe torque off function, see the

Hardware Manual

of the drive, and

Application guide

- Safe torque off function for ACSM1, ACS850 and ACQ810 drives

(3AFE68929814

[English]).

Switched supply and motor cabling (parameter

The drive can detect if the supply and motor cables have accidentally been switched
(for example, if the supply is connected to the motor connection of the drive). The
parameter selects if a fault is generated or not.

Stall protection (parameters

)

The drive protects the motor in a stall situation. It is possible to adjust the supervision
limits (current, frequency and time) and choose how the drive reacts to a motor stall
condition.

Automatic fault reset

The drive can automatically reset itself after overcurrent, overvoltage, undervoltage,
external and “analog input below minimum” faults. By default, automatic resets are off
and must be separately activated by the user.

Settings

Parameter group

32 Automatic reset

(page

Diagnostics

Parameter

(page

«
...
78
79
80
81
82
...
»

Содержание ACQ810

























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды