ABB ACQ810 Скачать руководство пользователя страница 258 | Manualshive

Страница: 258 / 376

ABB ACQ810 Скачать руководство пользователя страница 258

258 Parameters

78.03

Interlock mode

Defines whether interlocks are used or not. This parameter
is only valid in traditional pump control.

WARNING!

Use of the Autochange function also

requires the use of interlocks.
Interlocks are used in applications where one pump

at a time is connected to the output of the drive. The
remaining pumps are powered from the supply and
started/stopped by the relay outputs of the drive.
A contact of the manual on/off switch (or protective device,
such as a thermal relay) of each pump is wired to the
selected interlock input. The logic will detect if the pump is
unavailable and start the next available pump instead.
The interlock inputs are defined by parameters

If the interlock circuit of the speed-regulated pump (the pump
connected to the drive output) is switched off, the pump is
stopped and all relay outputs are de-energized. Then the
drive will restart. The next available pump in the Autochange
sequence will be started as the regulated pump.
If the interlock circuit of a direct-on-line pump is switched off,
the drive will not try to start that pump until the interlock
circuit is switched on again. The other pumps will operate
normally.

Not used

Interlocks not used.

0

On

Interlocks in use.

1

No.

Name/Value

Description

FbEq

«
...
256
257
258
259
260
...
»

Содержание ACQ810

























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды