ABB ACQ810 Скачать руководство пользователя страница 250 | Manualshive

Страница: 250 / 376

ABB ACQ810 Скачать руководство пользователя страница 250

250 Parameters

75.25

Drive start dly

Start delay for the pump that is directly controlled by the
drive. This does not affect the starting of the auxiliary pumps.

WARNING!

There must always be a delay set if the

pumps are equipped with star-delta starters. The
delay must be set longer than the time setting of the

starter. After the pump is switched on by the relay output of
the drive, there must be enough time for the star-delta starter
to first switch to star and then back to delta before the pump
is connected to the drive.

0…600 s

Start delay for drive-controlled pump.

1 = 1 s

75.26

Master speed acc

Defines the acceleration time in case the latest reference
received by the drive is higher than the previous reference.
This is likely to happen when the master status is passed on
from one drive to another. The parameter sets the ramp-up
time as seconds from zero to maximum frequency (

not

from

previous reference to new reference).
The parameter is effective only in the

follower modes. See parameter

Follower mode

0…1800 s

Acceleration time.

1 = 1 s

75.27

Master speed dec

Defines the acceleration time in case the latest reference
received by the drive is lower than the previous reference.
This is likely to happen when the master status is passed on
from one drive to another. The parameter sets the ramp-
down time as seconds from maximum frequency to zero (

not

from previous reference to new reference).
The parameter is effective only in the

follower modes. See parameter

Follower mode

0…1800 s

Deceleration time.

1 = 1 s

76

76 MF communication

Communication configuration for applications consisting of
multiple pumps with dedicated drives.

76.01

Enable MF comm

Enables/disables drive-to-drive communication through the
D2D link.

Note:

Drive-to-drive communication can only be enabled if

the embedded fieldbus interface is disabled (parameter

Protocol ena sel

is set to

No

Drive-to-drive communication disabled.

0

Yes

Drive-to-drive communication enabled.

1

76.02

Pump node

Node number of the drive on the drive-to-drive link.

Notes:

• Each drive on the link must have a unique node number.
• If the drive is not given a priority class, the node number is

also used in determining the starting order of pumps.

0…8

Node number.

1 = 1

76.03

Master enable

Determines (or defines a source that determines) if the drive
is allowed to be master on the drive-to-drive link.

No

The drive can only be a follower on the drive-to-drive link.

0

Yes

The drive is allowed to be master on the drive-to-drive link.

1

Const

Bit pointer setting (see

Terms and abbreviations

on page

).

-

Pointer

No.

Name/Value

Description

FbEq

«
...
248
249
250
251
252
...
»

Содержание ACQ810

























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды