manualshive.com logo in svg

ABB ACQ810, Руководство по прошивке

Поделиться
Скачать
ABB ACQ810 Скачать руководство пользователя страница 117

Parameters   117

02.24

FBA main sw

Internal Status word of the drive to be sent through the 
fieldbus adapter interface. See also chapter 

Control through 

a fieldbus adapter

 on page 

357

.

-

No.

Name/Value

Description

FbEq

Bit

Name

Value Information

0

Ready

1

Drive is ready to receive start command.

0

Drive is not ready.

1

Enabled

1

External run enable signal is received.

0

No external run enable signal is received.

2

Relay 
running

1

Drive is modulating.

0

Drive is not modulating.

3

Ref 
running

1

Normal operation is enabled. Drive is running and following given 
reference.

0

Normal operation is disabled. Drive is not following given reference 
(for example, it is modulating during magnetization).

4

Em  off 
(OFF2)

1

Emergency OFF2 is active.

0

Emergency OFF2 is inactive.

5

Em  stop 
(OFF3)

1

Emergency stop OFF3 (ramp stop) is active.

0

Emergency stop OFF3 is inactive.

6

Ack 
startinh

1

Start inhibit is active.

0

Start inhibit is inactive.

7

Alarm

1

An alarm is active. See chapter 

Fault tracing

 on page 

313

0

No alarm is active.

8

At setpoint

1

Drive is at setpoint. Actual value equals reference value (i.e. the 
difference between the actual speed and speed reference is within 
the speed window defined by parameter 

19.10

 

Speed window

).

0

Drive has not reached setpoint.

(continued)

Содержание ACQ810

























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды