ABB ACQ810 Скачать руководство пользователя страница 255

Страница: 255 / 376

Parameters 255

77.05

Sleep ext sel

Defines a source that is used by parameter

, selections

. See the

descriptions of those selections for the usage of this signal
source.

Not used

No source selected.

DI1

Digital input DI1 (as indicated by

02.01

DI status

, bit 0).

1073742337

DI2

Digital input DI2 (as indicated by

02.01

DI status

, bit 1).

1073807873

DI3

Digital input DI3 (as indicated by

02.01

DI status

, bit 2).

1073873409

DI4

Digital input DI4 (as indicated by

02.01

DI status

, bit 3).

1073938945

DI5

Digital input DI5 (as indicated by

02.01

DI status

, bit 4).

1074004481

Const

Bit pointer setting (see

Terms and abbreviations

on page

109

Pointer

77.06

Sleep boost step

When the drive is entering sleep mode, the setpoint is
increased by this percentage for the time defined by
parameter

77.07

Sleep boost time

No auxiliary pumps are started. If active, sleep boost is
aborted when the drive wakes up. See the diagram in
section

Sleep function

(starting page

0.00 … 32767.00 %

Sleep boost step.

100 = 1%

77.07

Sleep boost time

Sets the boost time for the sleep boost step defined by
parameter

77.06

Sleep boost step

0…100 s

Sleep boost time.

1 = 1 s

77.08

Wake up mode sel

Selects the signal that is compared to the wake up level

77.10

Wake up level

, and the condition that must be true for

the drive to wake up.
If the selected condition does not remain true until the wake-
up delay (

77.11

Wake up delay

) expires, the delay counter is

reset.

Wake > ref

If the process actual value (see group

28 Procact sel

)

remains below the process setpoint (see group

29 Setpoint

sel

) multiplied by the wake-up level for longer than the wake-

up delay (

77.11

Wake up delay

), the drive wakes up. See the

diagram below.

No.

Name/Value

Description

FbEq

Process setpoint × Wake-up level (

77.10

) / 100

Process actual value

Wake-up delay (

77.11

)

Time

SLEEPING

Содержание ACQ810
























































































































































































































































































































































































Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды

ABB ACQ810, Руководство по прошивке

Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды