ABB ACQ810 Скачать руководство пользователя страница 12

Страница: 12 / 376

12 About the manual

Contents

The manual consists of the following chapters:

•

The ACQ810 control panel

provides a description and instructions for use of the

control panel.

•

Control locations

describes the control locations and operation modes of the

drive.

•

Program features

contains descriptions of the features of the ACQ810 standard

program.

•

Application macros

contains a short description of each macro together with a

connection diagram.

•

Parameters

describes the parameters of the drive.

•

Additional parameter data

contains further information on the parameters.

•

Fault tracing

lists the alarm (warning) and fault messages with possible causes

and remedies.

•

Control through the embedded fieldbus interface

describes the communication to

and from a fieldbus network using the embedded fieldbus interface.

•

Control through a fieldbus adapter

describes the communication to and from a

fieldbus network using an optional fieldbus adapter module.

•

Control block diagrams

contains a graphical representation of the control

program.

Terms and abbreviations

Term/abbreviation

Definition

Analog input; interface for analog input signals

Analog output; interface for analog output signals

DC link

DC circuit between rectifier and inverter

Digital input; interface for digital input signals

DIO

Digital input/output; interface for digital input or output signals

Digital output; interface for digital output signals

DTC

Direct torque control

EFB

Embedded fieldbus

FBA

Fieldbus adapter

FIO-11

Optional analog I/O extension module

FIO-21

Optional analog/digital I/O extension module

FIO-31

Optional digital I/O extension module

FDNA-0x

Optional DeviceNet adapter

FENA-0x

Optional Ethernet/IP adapter

FLON-0x

Optional L

ORKS®

adapter

FPBA-0x

Optional PROFIBUS DP adapter

FSCA-0x

Optional Modbus adapter

Содержание ACQ810
























































































































































































































































































































































































Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды

ABB ACQ810, Руководство по прошивке

Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды