ABB ACQ810 Скачать руководство пользователя страница 332

Страница: 332 / 376

332 Control through the embedded fieldbus interface

Setting up the embedded fieldbus interface

Set the drive up for the embedded fieldbus communication with the parameters
shown in the table below. The

Setting for fieldbus control

column gives either the

value to use or the default value. The

Function/Information column

gives a

description of the parameter or instructs in its use.

The new settings will take effect when the drive is powered up the next time, or when
parameter

58.10

Refresh settings

is activated.

Parameter

Setting for
fieldbus control

Function/Information

COMMUNICATION INITIALIZATION

50.15 Fb cw used

P.02.36 (default)

Selects the address of the Fieldbus control
word in use (

Initializes embedded fieldbus communication.

EMBEDDED MODBUS CONFIGURATION

58.03 Node address

1 (default)

Node address. There may not be two nodes
with the same node address online.

58.04 Baud rate

9600 (default)

Defines the communication speed of the link.
Use the same setting as in the master station.

58.05 Parity

8 none 1

(default)

Selects the parity and stop bit setting. Use the
same setting as in the master station.

58.06 Control profile ABB Enhanced

(default)

Selects the communication profile used by the
drive. See section

Basics of the embedded

on page

600 (default)

Defines the timeout limit for the EFB
communication monitoring.

58.08 Comm loss

mode

None

(default)

Enables/disables EFB communication loss
monitoring and defines the means for resetting
the counter of the communication loss delay.

58.09 Comm loss

action

None

(default)

Defines the drive operation after the EFB
communication loss monitoring awakes.

58.10 Refresh

settings

Done

(default)

Refreshes the settings of parameters

58.01

…

58.09

58.30 Transmit delay

0 (default)

Defines the delay time which the slave waits
until it sends a response.

58.31 Ret app errors Yes

(default)

Selects whether the drive returns Modbus
exception codes or not.

58.32 Word order

LSW MSW

(default)

Defines the order of the data words in the
Modbus frame.

Содержание ACQ810
























































































































































































































































































































































































Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды

ABB ACQ810, Руководство по прошивке

Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды