ABB ACQ810 Скачать руководство пользователя страница 355

Страница: 355 / 376

Control through the embedded fieldbus interface 355

Modbus exception codes

Table below shows the Modbus exception codes supported by the embedded
fieldbus interface.

Code

Name

Description

0x01

ILLEGAL FUNCTION

The function code received in the query is not an
allowable action for the server.

0x02

ILLEGAL DATA
ADDRESS

The data address received in the query is not an
allowable address for the server.

0x03

ILLEGAL DATA VALUE

A value contained in the query in not an allowable
value for the server.

0x04

SLAVE DEVICE
FAILURE

An unrecoverable error occurred while the server was
attempting to perform the requested action.

0x06

SLAVE DEVICE BUSY

The server is engaged in processing a long-duration
program command.

Содержание ACQ810
























































































































































































































































































































































































Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды

ABB ACQ810, Руководство по прошивке

Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды