ABB ACQ810 Скачать руководство пользователя страница 316 | Manualshive

Страница: 316 / 376

ABB ACQ810 Скачать руководство пользователя страница 316

316 Fault tracing

2035

PS COMM
(0x5480)

b3

Communication errors
detected between the JCU
Control Unit and the power
unit of the drive.

Check the connections between the JCU
Control Unit and the power unit.

2036

RESTORE
(0x6300)

b4

Restoration of backed-up
parameters failed.

Contact your local ABB representative.

2037

CUR MEAS
CALIBRATION
(0x2280)

b5

Current measurement
calibration will occur at next
start.

Informative alarm.

2039

EARTH FAULT
(0x2330)

b7

Programmable alarm:

Drive has detected load
unbalance typically due to
earth fault in motor or motor
cable.

Check there are no power factor
correction capacitors or surge absorbers
in motor cable.
Check for an earth fault in motor or motor
cables by measuring the insulation
resistances of motor and motor cable.
If no earth fault can be detected, contact
your local ABB representative.

2040

AUTORESET
(0x6080)

b8

A fault is to be autoreset.

Informative alarm. See parameter group

32 Automatic reset

.

2041

MOTOR NOM VALUE
(0x6383)

b9

The motor configuration
parameters are set
incorrectly.

Check the settings of the motor
configuration parameters in group 99.

The drive is not
dimensioned correctly.

Check that the drive is sized correctly for
the motor.

2043

STALL
(0x7121)

b11

Programmable alarm:

Stall function

Motor is operating in stall
region because of e.g.
excessive load or
insufficient motor power.

Check motor load and drive ratings.
Check fault function parameters.

2044

LCURVE
(0x2312)

b12

Programmable alarm:

Overload func

/

Underload func

Overload or underload limit
has been exceeded.

Check the settings of the parameters in
group

34 User load curve

.

2045

LCURVE PAR
(0x6320)

b13

The load curve has been
incorrectly or inconsistently
defined.

Check the settings of the parameters in
group

34 User load curve

.

2046

FLUX REF PAR
(0x6320)

b14

The

U/f

(voltage/frequency)

curve has been incorrectly
or inconsistently defined.

Check the settings of the parameters in
group

.

2048

OPTION COMM LOSS
(0x7000)

b0

Communication between
drive and option module
(FEN-xx and/or FIO-xx) is
lost.

Check that option modules are properly
connected to Slot 1 (or) Slot 2.
Check that option modules or Slot 1/2
connectors are not damaged. To
determine whether module or connector
is damaged: Test each module
individually in Slot 1 and Slot 2.

Code

Alarm (fieldbus code),
other information

Cause

What to do

«
...
314
315
316
317
318
...
»

Содержание ACQ810

























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды