ABB ACQ810 Скачать руководство пользователя страница 197

Страница: 197 / 376

Parameters 197

30.09

Stall function

Selects how the drive reacts to a motor stall condition.
A stall condition is defined as follows:
• The drive is at stall current limit (

30.10

Stall curr lim

)

, and

• the output frequency is below the level set by parameter

30.11

Stall freq hi

, and

• the conditions above have been valid longer than the time

set by parameter

30.12

Stall time

See section

Stall protection (parameters 30.09…30.12)

page

30.10

Stall curr lim

Stall current limit in percent of the nominal current of the
motor. See parameter

30.09

Stall function

0.0 … 1600.0%

Stall current limit.

10 = 1%

30.11

Stall freq hi

Stall frequency limit. See parameter

30.09

Stall function

Note:

Setting the limit below 10 Hz is not recommended.

0.5 … 1000.0 Hz

Stall frequency limit.

10 = 1 Hz

30.12

Stall time

Stall time. See parameter

30.09

Stall function

0 … 3600 s

Stall time.

1 = 1 s

31 Motor therm prot

Motor temperature measurement and thermal protection
settings.

31.01

Mot temp1 prot

Selects how the drive reacts when motor overtemperature is
detected by motor thermal protection 1.

Motor thermal protection 1 inactive.

Alarm

The drive generates alarm

MOTOR TEMPERATURE

(0x4310)

if the temperature exceeds the alarm level defined

by parameter

31.03

Mot temp1 almLim

Fault

The drive generates alarm

or trips on fault

the temperature exceeds the alarm/fault level defined by
parameter

(whichever is lower).

No.

Name/Value

Description

FbEq

Bit

Function

Ena sup (Enable supervision)
0 = Disabled: Supervision disabled.
1 = Enabled: Supervision enabled.

Ena warn (Enable warning)
0 = Disabled
1 = Enabled: Drive generates alarm

STALL

(0x7121)

upon a stall condition.

Ena fault (Enable fault)
0 = Disabled
1 = Enabled: Drive trips on fault

STALL

(0x7121)

upon a stall condition.

Содержание ACQ810
























































































































































































































































































































































































Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды

ABB ACQ810, Руководство по прошивке

Результаты поиска

Содержание ACQ810

Отзывы:

Бренды по названию

Популярные бренды