ABB ACQ810 Скачать руководство пользователя страница 325 | Manualshive

Страница: 325 / 376

ABB ACQ810 Скачать руководство пользователя страница 325

Fault tracing 325

0056

TECH LIB CRITICAL
(0x6382)

Permanent fault generated
by a technology library.

Refer to the documentation of the
technology library.

0057

FORCED TRIP
(0xFF90)

Generic Drive
Communication Profile trip
command.

Check PLC status.

0058

FB PAR ERROR
(0x6320)

The drive does not have a
functionality requested by
PLC, or requested
functionality has not been
activated.

Check PLC programming.
Check settings of parameter group

.

0059

STALL
(0x7121)

Programmable fault:

Stall function

Motor is operating in stall
region because of e.g.
excessive load or
insufficient motor power.

Check motor load and drive ratings.
Check fault function parameters.

0060

LOAD CURVE
(0x2312)

Programmable fault:

Overload func

Underload func

Overload or underload limit
has been exceeded.

Check the settings of the parameters in
group

34 User load curve

0063

MOTOR TEMP2
(0x4313)

Programmable fault:

Mot temp2 prot

Estimated motor
temperature (based on
motor thermal model) has
exceeded fault limit defined
by parameter

.

Check motor ratings and load.
Let motor cool down. Ensure proper
motor cooling: Check cooling fan, clean
cooling surfaces, etc.
Check value of alarm limit.
Check motor thermal model settings
(parameters

…

).

Measured motor
temperature has exceeded
fault limit defined by
parameter

.

Check that actual number of sensors
corresponds to value set by parameter

Mot temp2 src

.

Check motor ratings and load.
Let motor cool down. Ensure proper
motor cooling: Check cooling fan, clean
cooling surfaces, etc.
Check value of alarm limit.

0064

IGBT OVERLOAD
(0x5482)

Excessive IGBT junction to
case temperature. This fault
protects the IGBT(s) and
can be activated by a short
circuit in the motor cable.

Check motor cable.

0065

IGBT TEMP
(0x4210)

Drive IGBT temperature is
excessive.

Check ambient conditions.
Check air flow and fan operation.
Check heatsink fins for dust pick-up.
Check motor power against drive power.

0066

COOLING
(0x4290)

Drive module temperature is
excessive.

Check setting of parameter

Check ambient temperature. If it exceeds
40 °C (104 °F), ensure that load current
does not exceed derated load capacity of
drive. See appropriate

Hardware Manual.

Check drive module cooling air flow and
fan operation.
Check inside of cabinet and heatsink of
drive module for dust pick-up. Clean
whenever necessary.

Code

Fault (fieldbus code),
other information

Cause

What to do

«
...
323
324
325
326
327
...
»

Содержание ACQ810

























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды