manualshive.com logo in svg

ABB ACQ810, Руководство по прошивке

Поделиться
Скачать
ABB ACQ810 Скачать руководство пользователя страница 243

Parameters   243

Multipump

Multiple drives, each controlling a separate pump, are 
connected together using the drive-to-drive link.

3

75.02

Nbr of pumps

Total number of pumps used in the application, including the 
pump connected directly to the drive.

0…8

Number of pumps.

1 = 1

75.03

Follower mode

Selects the source of reference when the drive is a follower.

Const speed

Follower drives are started and stopped by the control logic 
in the master drive. The master receives its reference from 
the PI controller.
When flow demand increases, new pumps are started.
If parameter 

76.10

 

Master location

 is set to 

In start

, the latest 

drive to start becomes the master; at the same time, the 
previously-started drive becomes a follower and starts to 
follow the reference defined by parameter 

75.04

 

Follower 

ref

.

If parameter 

76.10

 

Master location

 is set to 

Stable

, the drive 

that was started first remains the master.

0

See also the diagrams at parameter 

75.04

 

Follower ref

.

No.

Name/Value

Description

FbEq

Frequency

Flow demand

75.04

 

Follower 

ref

Drive status

Master

Follower

Drive 1

Stopped

Master

Follower

Drive 2

Stopped

Master

Drive 3

Dr

iv

e 

1

D

riv

e 

2

D

riv

e 

3

Содержание ACQ810

























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды