ABB ACQ810 Скачать руководство пользователя страница 259 | Manualshive

Страница: 259 / 376

ABB ACQ810 Скачать руководство пользователя страница 259

Parameters 259

78.04

Autochg level

Speed limit for the Autochange function when parameter

Autochg style

is set to

.

This parameter is only valid in traditional pump control.
The pump starting sequence is changed when the
Autochange interval has elapsed and the drive speed is
below this limit. Autochanging is indicated by a warning on
the control panel display.

Notes:

• The value of this parameter must be within the allowed

range (between minimum and maximum limits).
Otherwise no Autochanging is possible.

• When the drive is powered off, the values of the starting

sequence counter and the Autochange interval counter
are stored. The counters will continue from these values
after the drive is powered on.

Example:

There are three pumps in a system (parameter

is set to 3). Autochange level is set to

1500 rpm.
An Autochange occurs when the drive speed is below 1500
rpm, and the Autochange interval has elapsed since the
previous Autochange. Upon the Autochange,
1. All pumps are stopped
2. The starting sequence is incremented (from 1-2-3 to

2-3-1, etc.)

3. The contactor that controls the speed-regulated pump is

closed

4. The delay set by parameter

Drive start dly

passes

5. The speed-regulated pump is energized and normal

operation starts.

If the Autochange level is 0 rpm and the interval has
elapsed, Autochange will occur during a stop (for example,
when the Sleep function is active).

0…32767 rpm

Autochange level.

1 = 1 rpm

78.05

Autochg interval

Specifies the Autochange interval. See parameter

Autochg level

0.00 … 1092.25 h

Autochange interval.

100 = 1 h

78.06

Interlock pump 1

Selects the input (or signal) for status of pump 1.
When the input is 1, the drive assumes the pump is in use
and can be started.

Not used

The interlock is off, meaning that the pump is not in use.

0

On

The interlock is on, meaning that the pump is ready for use.

1

DI1

Digital input DI1 (as indicated by

, bit 0).

1073742337

DI2

Digital input DI2 (as indicated by

, bit 1).

1073807873

DI3

Digital input DI3 (as indicated by

, bit 2).

1073873409

DI4

Digital input DI4 (as indicated by

, bit 3).

1073938945

DI5

Digital input DI5 (as indicated by

, bit 4).

1074004481

Const

Bit pointer setting (see

Terms and abbreviations

on page

-

Pointer

78.07

Interlock pump 2

Selects the input (or signal) for status of pump 2.
When the input is 1, the drive assumes the pump is in use
and can be started.

Not used

The interlock is off, meaning that the pump is not in use.

0

No.

Name/Value

Description

FbEq

«
...
257
258
259
260
261
...
»

Содержание ACQ810

























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды