Xerox WC5545F, Service Manual

Page: 936 / 2320

August 2007
2-744
WorkCentre 5687 Family
OF4a
Status Indicator RAPs
05-522 Raise document handler Sheet left over DADH CVT
sensor after jam Remove sheet. Perform
05-350, 05-352 RAP
05-523 Raise document handler Sheet left over DADH registra-
tion sensor after jam Remove sheet. Perform
05-340 RAP
05-524 Raise document handler Sheet left over DADH exit sen-
sor after jam Remove sheet. Perform
05-345, 05-346 RAP
05-525 Remove all documents
from the document han-
dler tray Sheet left over DADH docu-
ment present sensor after jam Remove sheet. Perform
05B RAP
05-526 Open document handler
top cover DADH - sheet near CVT sen-
sor in duplex path. 05-352 fault
is raised Reset when DADH top
cover closed after jam
cleared. Perform 05-
350, 05-352 RAP
05-530 No message Document in DADH tray Remove document
from tray. Perform 05B
RAP
05-531 No message Document in DADH area 2
with no document in area 3 Remove document.
Perform 05-330, 05-
331, 05-335, 05-340
RAPs.
05-532 No message Document in DADH area 2
with document in area 3 Remove document.
Perform RAP. Perform
05-330, 05-331, 05-
335, 05-340 RAPs.
05-533 No message Document in DADH area 3 Remove document.
Perform RAP. Perform
05-330, 05-331, 05-
335, 05-340 RAPs.
05-534 Check for a stray original
in the document tray Unscheduled document
detected by any sensor Clear the document
path in the DADH. Per-
form 05-330, 05-331,
05-335, 05-340, 05-
345, 05-346 RAPs.
05-535 Document is too short to
be scanned by the docu-
ment handler, use the doc-
ument glass Open DADH cover Close document han-
dler cover. Perform 05-
310 RAP
05-536 Close document handler Open document handler Close document han-
dler. Perform 05-300
RAP
05-537 No message DADH tray empty Put document in tray.
Perform 05B RAP
05-538 Document handler is
unavailable DADH not available. 03-322,
03-323 or 03-324 raised Perform 03-320, 03-
322 to 03-324 RAP and
14-320 RAP
Table 5 05-5XX Status codes
Status
Code
UI Message Reason for Message Reference / Action
05-539 Document handler feed
roll has been replaced DADH feed head CRU
replaced. Message automati-
cally cleared half a second
after setting None
05-540 Resort and reload all origi-
nals. DADH document jam is
cleared for a single job Replace document on
DADH input tray to
enable recovery. Check
for blanks in output tray.
Resume or cancel job
05-542 Document Handler is
unavailable DADH document transport
needs service Perform 05A RAP
05-544 Resort and reload ALL the
originals Document jam is cleared (cov-
ers cycled and switch cleared)
and ‘normal job’ or ‘build job’ Resume job command
is given with documents
replaced in input tray, if
required, or cancel job
command is given
05-546 Reload originals or select
original size and press
Start On pre-feed the DADH fails to
recognize the size of the docu-
ment Reload originals or
select size. Perform
05C RAP
05-547 Re-order but do not
replace Document Han-
dler Feed Roll DADH feed roll assembly near
end of life Re-order feed roll
assembly PL 5.15 Item
1.
05-548 Please follow the instruc-
tions below to replace the
document handler feed
roll: DADH feed roll assembly at
end of life Install a new feed roll
assembly, PL 5.15 Item
1.
05-560 Document is too short to
be scanned by the docu-
ment handler, use the doc-
ument glass Document too short for DADH,
use document glass. Fault 05-
310 raised Remove document
from DADH during jam
clearance, Perform 05-
310 RAP
05-586 Try turning the machine off
and on. Please call for
assistance if the problem
persists Network controller software
version supplied at power-on is
not compatible with image pro-
cessor PWB. Fault 03-416 is
raised Perform 03-340, 03-
416 RAP. If necessary,
reload the software, GP
4
05-588 Try turning the machine off
and on. Please call for
assistance if the problem
persists Finisher software version sup-
plied is not compatible. Fault
03-418 raised Perform 03-360, 03-
408 to 03-410, 03-418
RAP If necessary,
reload the software, GP
4
Table 5 05-5XX Status codes
Status
Code
UI Message Reason for Message Reference / Action