Xerox WC5545F, Service Manual

Page: 1979 / 2320

August 2007
6-87
WorkCentre 5687 Family
dC131b
General Procedures & Information
12-011 BookMkrTriFold-
Deskew Used to adjust the amount
of deskew for the 2nd fold in
a tri-fold by varying the
amount of buckle length in
registration for the paper
entering TF. 90 to 110 100
12-012 BookMkrStapleOff-
setM Used to control the staple
offset position for 8.5x11
and 8.5x14 paper. HVF BM
only. 0 to 200
0.1137mm/step 100
12-013 BookMkrStapleOff-
setL Used to control the staple
offset position for 11x17 and
A3 paper. HVF BM only. 0 to 200
0.1137mm/step 100
12-050 FinisherSoftCyc-
Time Time out for soft cycling of
finisher to time seconds 0 to 60 sec-
onds 32/38=40
45=35
55//65/75/
87=30
Table 2 NVM chain 14
Location NVM Name NVM Description Value Default
14-001 DADH Centre Reg DADH CVT centre registra-
tion 3513 to 3770
pixels 32/38/45/
55=3563
65/75/87=3720
14-002 DADH LE Reg DADH lead edge registra-
tion 0 to 150 scan
lines 70
14-003 Platen Top Edge
Reg Platen top edge registration 7056 to 7313
pixels
32/38/45/
55=7106
65/75/87=7263
14-004 Platen Lead Edge
Reg Platen lead edge registra-
tion 0 to 150 scan
lines 70
14-012 Scanner CVT posi-
tion Adjusts position of scan car-
riage at the CVT position 4868 to 4898
0.1mm incre-
ments 32/38/45/
55=4988
65/75/87=4878
14-013 Scanner Doc Size
Pos Adjusts position of scan car-
riage at the document size
position 0 to 5000
0.1mm incre-
ments 32/38/45/
55=700
65/75/87=500
14-014 Scanner LE Hotline Scanner lead edge active
hot line
200 to 500
0.1mm incre-
ments 32/38/45/
55=350
65/75/87=230
14-025 Scan CCD Gain
Setpt To adjust pixel gain set point
during scanner CCD calibra-
tion 150 to 255
increments of
1 bit 32/38/45/
55=212
65/75/87=214
14-026 Scan CCD Offset
Pnt To adjust offset point during
scanner CCD calibration 0 to 20 Incre-
ments of 1 bit 0
Table 1 NVM chain 12
Location NVM Name NVM Description Value Default
14-027 Scanner Mag Adj Adjust platen scan speed in
slow scan direction to com-
pensate for magnification
errors 50 to 150 100
14-028 Green Gain Set
point Nvm Green scan calibration set-
ting. 150 to255 200
14-029 Red Gain Set point
Nvm Red scan calibration setting. 150 to255 195
14-030 Blue Gain Set point
Nvm Blue scan calibration set-
ting. 150 to255 203
14-031 Red Sako Adjust
Nvm Red colour balance adjust-
ment setting. 0 to 200 100
14-032 Green Sako Adjust
Nvm Green colour balance
adjustment setting. 0 to 200 100
14-033 Blue Sako Adjust
Nvm Blue colour balance adjust-
ment setting. 0 to 200 100
14-034 Light Sako Adjust
Nvm Lighten/Darken balance
adjustment setting. 0 to 200 100
Table 3 NVM chain 15
Location NVM Name NVM Description Value Default
15-005 ScannerFSResolu-
tion To provide configuration sup-
port for scanners with Fast
Scan resolutions of 400 dpi and
600 dpi. 400 or 600 600
15-006 Scanner Direction To provide configuration sup-
port for scanners with different
Fast Scan direction. 0=reverse
1=forward 1
15-007 CVT scanning
image gain adjust-
ment Percentage increase with
respect to document glass
scanning gain. 0 to 20% 10
Table 4 NVM chain 17 (image disk drive not used)
Location NVM Name NVM Description Value Default
17-001 Disk Mode Disk present. 1=enabled
0=disabled 0
17-002 Disk spin up
delay Time before image disk
receives power 0 to 30 seconds 10
Table 5 NVM chain 19
Location NVM Name NVM Description Value Default
19-001 Megs of Mem-
ory Amount of memory installed 0 to 65535M 16
Table 2 NVM chain 14
Location NVM Name NVM Description Value Default