Xerox WC5545F, Service Manual

Page: 968 / 2320

August 2007
2-776
WorkCentre 5687 Family
OF4b
Status Indicator RAPs
Please check the output bin
for blank and partially
imaged sheets and discard
them 03-510 When paper is delivered to the
output and a video complete
has not been received by the
image processor Perform 03-423, 424,
433, 434, 821, 822,
831, 832 RAP
Please close the Booklet
Maker Stapler module 11-921 The stapler position sensor
indicates the stapler module is
not closed in initialisation Close the BM stapler
module. If necessary,
perform 11-063-171,
11-411-171 RAP for
staple unit 1, and 11-
403-171, 11-413-171,
11-414-171 RAP for
staple unit 2
Please delete the job. No
tray is configured with the
required paper size. Press
the Job Status button. Then
select the Delete Button. 22-504 No tray configured for media Configure one tray for
this stock size.
Please wait, adjusting fuser
temperature 10-540 Fuser temperature control fail-
ure. Perform 10-322, 10-
324, 10-325, 10-330,
10-370 RAP, 10-315,
10-320, 10-321, 10-
323, 10-340, 10-350,
10-360, 10-380 RAP
Please wait, freeing mem-
ory 19-502 Out of memory resources. Fault
19-401, 19-402 Perform 19-401, 19-
402, 19-403 RAP
Please wait. The system is
attempting to recover from
a fault 03-556 When fault codes 03-351 and
03-354 are raised Perform 03-350, 03-
351, 03-354 RAP
Please wait. The system
software and the network
controller are about to be
reset from a remote client.
The reset may take sev-
eral minutes. Any jobs cur-
rently being marked will be
cancelled 03-501 prtgeneralReset MIB object on
the network controller is set to a
value of powerCycleReset(4) None
Please wait, your job will
continue shortly. Do not
press the Start button again 19-506 Job delayed status High EPC usage. Per-
form 19-401, 19-402,
19-403 RAP
Please wait... The system
is attempting to recover 22-501 Attempting print recovery. 22-
306, 22-307, 22-309 Perform 22-306 to 22-
315, 22-801, 814 RAP
Table 3 Status messages O to R
UI Message
Status
Code
Reason for Message Reference / Action
Power down failure. Power
off cannot be completed.
Press the power button on
the left side of the machine.
If there is no response
within 1 minute, then
remove the power cord.
Wait 1 minute then reinsert
the power cord and switch
the machine on. 03-520 System fails to power off after
request from the UI Perform 03-374 RAP
Printing and scanning are
unavailable. Please call for
assistance 03-500 Voltage not present on 24 V rail
monitored by IOT Perform 03-480 RAP
Printing is unavailable 09-550 Photoreceptor erase lamp has
failed. 09-350 fault Perform 09-350 RAP
Pull out fuser module, then
firmly push it back in 03-547 IOT-FRU: unable to read from
FRU. Fault 03-371 is raised. Perform 03-371, 03-
372 RAP
Pull out xerographic mod-
ule, then firmly push it back
in 03-548 IOT-XRU: unable to read from
XRU. Fault 03-372 is raised. Perform 03-371, 03-
372 RAP
Punch Chad Bin Set State 11-541 The chad bin has been
removed from the finisher Reinstall the chad bin
Raise document handler 05-522 Sheet left over DADH CVT sen-
sor after jam Remove sheet
Raise document handler 05-523 Sheet left over DADH registra-
tion sensor after jam Remove sheet
Raise document handler 05-524 Sheet left over DADH exit sen-
sor after jam Remove sheet. Per-
form 05-345, 05-346
RAP
RARP functions are not
available. Please notify
machine administrator 16-594 Network controller - RARP
address resolution fails Connectivity fix and
switch off the machine
then switch on the
machine, GP 14.
Reload originals and press
start 14-566 CCD (width) and length sen-
sors cannot determine size of
the original Reposition originals
and press start, Per-
form 14A RAP
Reload originals and press
Start 05-503 Not enough originals during
recovery Reload originals
Reload originals or select
original size and press Start 05-546 On pre-feed the DADH fails to
recognize the size of the docu-
ment Reload originals or
select size. Perform
05C RAP
Remove documents from
the paper tray and close
the cover 05-502 Document present in DADH
tray with DADH cover open Lower the document
handler to scan your
documents. Perform
05-300 RAP
Table 3 Status messages O to R
UI Message
Status
Code
Reason for Message Reference / Action