Xerox WC5545F, Service Manual

Page: 933 / 2320

August 2007
2-741
WorkCentre 5687 Family
OF4a
Status Indicator RAPs
03-511 Output Bin full. Touch
pause to hold printing
while emptying the bin
The 90% full sensor is cleared
before the bin switch timer
expires. Printing will continue
automatically 15 sec-
onds after raised if the
Pause button is not
pressed.
Or when the Resume
button pressed.
Or Automatically 15
minutes after Pause
button pressed if
Resume button is not
pressed.
03-520 Power down failure.
Power off cannot be com-
pleted. Press the power
button on the left side of
the machine. If there is no
response within 1 minute,
then remove the power
cord. Wait 1 minute then
reinsert the power cord
and switch the machine
on.
System fails to power off after
request from the UI Perform 03-374 RAP
03-525 - Software upgrade NVM re-ini-
tialization Cleared when the
Image processing mod-
ule has completed ini-
tialization, the status will
clear
03-526 Restoring configuration
setting. Please wait. Sys-
tem will reboot when com-
pleted.
Software upgrade configura-
tion reset Cleared when the
Image processing mod-
ule has completed
restoring the configura-
tion settings the status
will clear
03-535 Please enter your pass-
word and press Enter
Machine in service copy mode
for password entry Status clears on leav-
ing service copy mode
03-536 No message Set on entry to diagnostics.
(intrusive diagnostic activity in
progress) Clears on leaving diag-
nostics
03-537 Software upgrade com-
pleting - please wait
Indicates machine in IOT soft-
ware upgrade status Clears on leaving IOT
software upgrade
Table 3 03-5XX Status codes
Status
Code
UI Message Reason for Message Reference / Action
03-538 An error has occurred -
The system is attempting
to recover
System attempting to recover
from an image processor to
IOT communication failure.
Fault 03-300 or 03-320 is
raised. Cleared if communica-
tion is established. Per-
form 03-300, 306, 461,
482, 805, 870 RAP, 03-
320, 03-322 to 03-324
RAP
03-539 An error has occurred.
The system is attempting
to recover.
Comms failure between the
IOT and Image processing Clears when comms re-
established, or is con-
verted to status code
03-540 after third recov-
ery attempt
03-540 Communications failure.
Please call for assistance
DC-IOT: three times retry fail at
100 ms cycle communication -
no response. The DC is unable
to communicate with the IOT
within one minute of power on
or after three retries Perform 03-340, 03-416
RAP
03-541 No message Image processing-UI: three
times retry fail at 100 ms cycle
communication - no response Perform 03-310 RAP
03-542 DADH fault. Please call
for assistance
Image processing-DADH:
three times retry fail at 100 ms
cycle communication - no
response Clear DADH of originals
- use document glass
for copy or Fax. Perform
03-320, 03-322 to 03-
324 RAP
03-543 Scanner fault. Please call
for assistance
Image processing-CCD: three
times retry fail at 100 ms cycle
communication - no response Perform 14-310 RAP
03-544 Network controller
unavailable. Please call
for assistance
Image processing-network
controller: three times retry fail
at 100 ms cycle communica-
tion - no response Switch off the machine
then switch on the
machine, GP 14. Per-
form 03-340, 03-416
RAP.
03-545 Output device communi-
cations fault. Please call
for assistance.
IOT-Finisher: three times retry
fail at 100 ms cycle communi-
cation - no response. 03-360 Perform 03-360, 03-408
to 03-410, 03-418 RAP
03-547 Pull out fuser module,
then firmly push it back in
IOT-Fuser comms fault. Fault
03-371 is raised. Perform 03-371, 03-372
RAP
03-548 Pull out xerographic mod-
ule, then firmly push it
back in
IOT-X-Crum comms fault.
Fault 03-372 is raised. Perform 03-371, 03-372
RAP
03-549 Paper Trays are unavail-
able. Call for assistance
IOT to trays 1 & 2 comms fault.
Fault 03-350 is raised. Perform 03-350, 03-
351, 03-354 RAP
Table 3 03-5XX Status codes
Status
Code
UI Message Reason for Message Reference / Action