Nortel Passport 8600 Series Installation Manual Download Page 31

Page: 31 / 164

Interface module descriptions

•

Packet over SONET (POS) OC-3c/STM-1 and OC-12c/STM-4 ports

•

Small form factor pluggable (SFP), 10 Gbps SFP (XFP), and Gigabit
interface converter (GBIC) optical ports

Interface modules navigation

•

“8608GBE and 8608GBM modules” (page 31)

•

“8608GTE and 8608GTM modules” (page 33)

•

“8608SXE module” (page 35)

•

“8616GTE module” (page 36)

•

“8616SXE module” (page 38)

•

“8624FXE module” (page 39)

•

“8632TXE and 8632TXM modules” (page 41)

•

“8648TXE and 8648TXM modules” (page 43)

•

“8672ATME and 8672ATMM modules” (page 45)

•

“8683POSM module” (page 46)

•

“8630GBR module” (page 48)

•

“8648GTR module” (page 50)

•

“8683XLR module” (page 52)

•

“8683XZR module” (page 54)

•

“8612XLRS module” (page 56)

•

“8634XGRS module” (page 58)

•

“8648GBRS module” (page 61)

•

“8648GTRS module” (page 62)

8608GBE and 8608GBM modules

The 8608GBE and 8608GBM modules provide eight bays for GBICs. Use
GBICs to provide riser connections, server attachments, or interswitch
links. The following figure shows the 8608GBE/GBM module.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 31 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: