manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 23 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 23

23

.

Ethernet Routing Switch 8600 module
fundamentals

The Ethernet Routing Switch 8600 modules provide a full complement
of core routing and switching capabilities. Use this section to help you
understand and use each interface module.

The Ethernet Routing Switch 8600 supports Power Management,
which allocates priority among installed modules. For more information
about Power Management, see Nortel Ethernet Routing Switch 8600
Administration, NN46205-600.

For the minimum Ethernet Routing Switch 8600 software versions required
to support the hardware described in this document, see Nortel Ethernet
Routing Switch 8600 Administration, NN46205-600.

Navigation

•

“Release 3.x module feature set” (page 24)

•

“Release 4.x module feature set” (page 24)

•

“Release 5.x module feature set” (page 26)

•

“Ethernet Routing Switch 8600 modes” (page 27)

•

“Chassis slots and modules” (page 29)

•

“Module removal and switch behavior considerations” (page 29)

•

“Interface module descriptions” (page 30)

•

“Nortel-qualified SFPs, XFPs, and GBICs” (page 64)

•

“SFPs, XFPs, R and RS modules, and power consumption” (page 66)

•

“SF/CPU modules” (page 67)

•

“Enterprise Enhanced CPU daughter card” (page 77)

•

“8661 SSL Acceleration Module” (page 78)

•

“Web Switching Module” (page 80)

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments