Nortel Passport 8600 Series Installation Manual Download Page 146

Page: 146 / 164

146

Technical specifications

Table 92
Pin assignments: DTE to DCE (cont’d.)

Switch

Modem

Signal

Pin number

DCE DB-9
pin number

DCE DB-25
pin number

TXD

DTR

GND

DSR

RTS

CTS

Port density for Ethernet Routing Switch 8600 modules

The following table provides port density information for each module.

Table 93
Port density for Ethernet Routing Switch 8600 modules

Maximum number of ports for each chassis

Module type

Port type

8003

8006

8010 and 8010co

E and M modules

1000BASE-SX

1000BASE-LX

1000BASE-ZX

1000BASE-XD

1000BASE-CW
DM

8608GBE and
8608GBM

1000BASE-T

8608GTE and
8608GTM

1000BASE-T

8608SXE

1000BASE-SX

8616GTE

1000BASE-T

128

8616SXE

1000BASE-SX

128

8624FXE

100BASE-FX

192

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 146 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: