Nortel Passport 8600 Series Installation Manual Download Page 123

Page: 123 / 164

8624FXE module

123

The following table provides optical specifications.

Table 50
8616SXE optical specifications

Optical specifications

Wavelength:

850 nm

Optical budget:

7 dB

Laser transmitter characteristics:

Minimum launch power: -10 dBm

Maximum launch power: -4 dBm

Receiver characteristics:

Minimum receiver sensitivity: -17 dBm

Maximum input power: 0 dBm

8624FXE module

The following table provides specifications for the 8624FXE modules.

Table 51
8624FXE specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

7.6 lb (3.4 kg)

Electrical specifications

Input power:

84.8 W maximum

Thermal rating:

289.2 Btu/hr maximum

MTBF rating

320 972 hr

Connector type

MT-RJ

Cable specifications

Type:

62.5 µm multimode fiber optic cable

Distance:

6562 ft (2 km) for full-duplex links

Optical specifications

Wavelength:

1300 nm

Optical budget:

15 dB

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 123 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: